Kenneth Crawford is a freelance writer with more than 10 years of experience. His work has appeared in both print and online publications, including "The American Chronicle. This series of faucets uses a ceramic disc cartridge to control water flow.

Like other faucets, when the cartridge becomes clogged or faulty, it is necessary to remove the handles to access the cartridge. Unlike other faucets, removing a Kohler Revival handle does not involve a set screw. The handle sits on top of a housing that threads into the faucet body. Turn off the water supply to the Kohler Revival faucet you are repairing.

There is a shut-off valve on the hot water and cold water lines under the sink. Turn the valve handles completely clockwise to turn off the water. Turn on the faucet handles to allow drainage of the remaining water in the line. Turn off the faucet handles. Hold the handle with one hand and rotate the bell housing counterclockwise with your free hand. The bell housing is the decorative housing between the handle and the base of the faucet. Place masking tape around the bell housing if it will not turn by hand.

Hold the handle and turn the bell housing with a pair of slip-joint pliers. The tape protects the bell housing finish. Lift the handle and the bell housing away from the faucet base. There is an O-ring on the inside edge of the housing. Ensure that you do not lose the O-ring, as it is necessary when reinstalling the handle. Pin Share Tweet Share Email. Things You'll Need Masking tape Slip-joint pliers.To take apart or remove a Kohler kitchen faucet, you only need a few simple tools.

It's an easy DIY project that you can tackle in less than 10 minutes as long as you don't run into any trouble with "frozen" or rusty bolts. You can take apart a Kohler faucet in three different ways: removing the handle to replace the cartridge, removing the aerator and removing the faucet altogether.

First things first: you need to turn the water off when accessing the cartridge or removing the faucet altogether. Hot and cold water shutoff valves should be located under your sink. Turn them both to the right, and then try turning on the faucet to confirm that you've successfully shut off the water.

Note that sometimes the water shutoff valves "freeze" from lack of use. In that case, you may need to try to shut off the main water valve. Depending on the problem, you may not need to remove your Kohler kitchen faucet. If your Kohler faucet is leaking from the spout or out of the handle, or the handles are too loose or too tight, you can remove the handle to access the cartridge.

Replacing this cartridge will fix leaks and mobility issues. Read more: How to Install a Kitchen Faucet. Look or feel behind the handle for a small oval. Slip a flat-head screwdriver under this oval tab to pop it off and reveal the hex nut.

how to remove kohler bathroom faucet cartridge

Use an Allen wrench to remove that nut and the handle. Next, twist the neck counterclockwise to remove it from the handle. Use an adjustable wrench to remove the kitchen faucet nut holding the cartridge down. Now you'll see the cartridge. It can sometimes be pulled out by hand, otherwise you may need to use needle-nose pliers to firmly pull it up and out. You don't need to worry about turning the water off if all you need to do is remove the aerator, according to the Kohler YouTube channel.

Your Kohler kitchen faucet may have a spout end that simply screws off by turning it clockwise. If it seems stuck, wrap a towel around the end before using an adjustable wrench to twist it off.

Then, just push the aerator out with your thumb. On your pull-down faucet, the aerator is surrounded by the spray face. Line up an adjustable wrench with the straight lines on the aerator and firmly pull it out. Read more: How to Fix a Faucet Aerator.

To remove a Kohler kitchen faucet completely, you'll need to disconnect the supply lines with the water off, of course. Use an adjustable wrench to unscrew these, and then reach under and behind the sink basins to feel for the screws that hold the faucet to the counter via a large washer.

Use a Phillips-head screwdriver to remove these screws. You may need to spray some WD if the screws seem too tight. Once the screws are removed and the supply lines are disconnected, you can simply pull up on the faucet and pull all components through the holes to complete the faucet removal. Cathy Habas enjoys distilling even the most complicated home improvement tasks into bite-sized pieces.

She believes in empowering homeowners one article at a time. Hunker may earn compensation through affiliate links in this story. Share this article.

how to remove kohler bathroom faucet cartridge

Cathy Habas. Show Comments.By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service.

It only takes a minute to sign up. The cold faucet is leaking, and I am trying to repair it by replacing the valve cartridge. However, for the love of god, I can't find a way to open the faucet so that I can replace the valve cartridge. I don't see a small opening anywhere and I can't seem to remove any top or tip of the faucet.

I tried to unscrew the handle, but I am stuck afterwards. Any help would be much appreciated. Give Kohler a call. All their products carry a lifetime warranty or at least they used to, They can explain the procedure you are looking for and send you the repair parts free to you. Usually on kohler you unscrew the pedestal.

On cold put a cloth around the pedestal use pliers turning counterclockwise. Sign up to join this community. The best answers are voted up and rise to the top. Home Questions Tags Users Unanswered. Asked 1 year ago. Active 2 months ago. Viewed 1k times.

It's a generic video, so the faucet featured there is not this particular faucet. Active Oldest Votes. Hello, and welcome to Home Improvement. Thanks for the answer; keep 'em coming. And, you should probably take our tour so you'll know how best to contribute here. Sign up or log in Sign up using Google. Sign up using Facebook. Sign up using Email and Password. Post as a guest Name. Email Required, but never shown. The Overflow Blog.

Q2 Community Roadmap.

how to remove kohler bathroom faucet cartridge

The Overflow How many jobs can be done at home? Featured on Meta. Community and Moderator guidelines for escalating issues via new response…. Feedback on Q2 Community Roadmap. Related 5. Hot Network Questions. Question feed.When working on your Kohler faucet, you must remove the bonnet to access the cartridge and O-rings. The bonnet covers the bonnet nut securing the cartridge or valve stem within the body of faucet.

The bonnet is the piece between the handle and the faucet body. Removing a Kohler bonnet is the same on all Kohler faucets; however, removing the handle to access the bonnet depends on the faucet type.

Turn off the water supply valves to the faucet you are repairing. Each faucet has two water supply lines from the house to the faucet. Each line has a shut off valve between the house pipe and the faucet supply lines. Turn the shut-off valve handles clockwise to turn off the water. Find the screw on your faucet handle that secures the handle to the faucet.

Subscribe to RSS

Single lever handles usually have a small set screw on the back of the faucet handle. Remove the set screw with an Allen wrench and pull the handle straight off. Some single handle faucets and rotary handles have a cap on top hiding the securing screw. Locate a notch between the edge of the cap and the handle. Pry the cap off with a flat-head screwdriver to reveal the securing screw. Remove the securing screws with a Phillips-head screwdriver and pull the handle off the faucet. Place a rubber jar lid remover pad around the bonnet and turn the bonnet counter-clockwise by hand.

If the bonnet does not budge, use a pair of pliers around the rubber pad to turn the bonnet. Unscrew the bonnet completely from the faucet body. Installation is the reverse of removal. A wet rag can be used in place of a rubber jar lid remover. The idea is to protect the finish of the bonnet. Kenneth Crawford is a freelance writer with more than 10 years of experience. His work has appeared in both print and online publications, including "The American Chronicle.

how to remove kohler bathroom faucet cartridge

Hunker may earn compensation through affiliate links in this story. Step 1 Turn off the water supply valves to the faucet you are repairing. Step 2 Find the screw on your faucet handle that secures the handle to the faucet.

Step 3 Place a rubber jar lid remover pad around the bonnet and turn the bonnet counter-clockwise by hand. Tip Installation is the reverse of removal.

Share this article. Kenneth Crawford. Show Comments.By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. It only takes a minute to sign up. It's still in the casing, as I didn't want to remove the whole faucet. I tried lots of WD and trying to tighten a little and then loosen. Someone told me to use a hair-dryer on it to heat it up a little.

The thing just won't budge. I think I may have ruined the "nut. My cold side cartridge needed replacement. My valve assembly has manufacture date of I have a number of same Kohler Lavatory sets and have had to replace a few valve assemblies a few times.

Kohler has sent me entire retrofit valve set because many times, as was described in prior comments, it's difficult to break the seal of the top nut to get at and replace the cartridge. I decided to get brave after reading the ideas from comments and decided to try to get at the cartridge. This is what worked for me.

I used a vice grip and attached it right below the threads of the assembly just above where the water line attaches to the assembly. It's machined there to accept a wrench and the vice grip secures perfectly. I took my ball pain hammer and tapped the nut area all around to hopefully break the seal.

I then placed the valve assembly on the garage floor with the vice grip attached. It is not reverse thread, and if it hasn't budged you just need to crank on it more -- don't worry about the retaining clip, it doesn't need to come off.

I would use a channel-lock wrench for this but a small pipe wrench will make the job a bit easier only because you won't have to squeeze the wrench while turning. You can try rapping on it with a hammer not too hard to break it loose also.

DIY Kohler Bathroom Sink Widespread Faucet Installation #Kohler #Faucet #DIYProjectsByDave

It is possible that you have to remove the entire valve assembly from the faucet first, because even when you crack it loose that cartridge might not come out of the top like you are planning; it might make your job easier as well.

You could also opt to get a new valve assembly if you really can't budge that cartridge. Edit: Here's a vid to give you an idea of what you are going for: youtube video. You should stop using your pliers to try and remove it as it looks like you've made things worse with that approach. Get a deep socket in precisely the correct size for this nut. If that doesn't fit anymore you may want to try some seriously tight vise-grips. I have Kohler bathroom faucets with separate handles, and the only way I was able to remove the cold cartridge, was to remove the cold water valve assembly.

I removed all the tubing, handle, chrome, nut, washers, until I had just the valve assembly with the cartridge at one end. I took a roll of masking tape and wrapped the valve body threads several times. In the plumbing department, I found a 2 foot pipe wrench and a 2 foot section of steel pipe. This rather large pipe wrench goes around the valve body, masking tape protects the threadsand I put my socket over the cartridge and the piece of pipe over the ratchet handle.

Then it's just a matter of applying enough force to remove the cartridge from the valve body. I have had to replace my cold water cartridges several times, due to all the Kohler faucets in my place, and it has worked every time for me.

Thanks to Home Depot for letting me borrow their stuff. Even though they were unaware, lol. Alternately, you can buy the complete valve assembly as a part, but it will have half the flow rate of the pre Kohler valves. And costs 3x more. I got the cartridge off Amazon, since Home Depot doesn't sell Kohler parts.You might need to replace bathroom faucet cartridge because it has started malfunctioning.

When you want to replace bathroom faucet cartridge, you should be keen to perform the process yourself. It is a very straightforward procedure as you will realize today.

You only need to remove the old faucet cartridge, and inserting the new one in place. Allow the best use of your bathroom sink and faucet by replacing the malfunctioning cartridge. I will advise you to replace the cartridge with the corresponding bathroom faucet model.

For example, we have Moen faucet whose best fitting cartridge would be a Moen cartridge. Due to unique features, make sure that the cartridge and the faucet model match. The basic knowledge that you need to understand today is that modern bathroom faucet cartridges are designed to help regulate water pressure and temperature. When these cartridges wear out, they stop functioning effectively.

You need to replace bathroom faucet cartridge in case you realize that the water flow rate is below par. Down here, I discuss with you how the replacement process is undertaken. Before everything else, ensure the process starts with turning off the water supply lines.

You can have to turn the water supply valves in a clockwise direction until no water can drip. In brief, you need to replace bathroom faucet cartridge whose performance is below par.

It will take you a lot of time to fill a bucket of water. If you notice any abnormal behavior in the flow of water, the suspect might be the faucet cartridge. It might have worn out, thus prompting you to buy a new one to replace the old cartridge.

I hope this article has been helpful in this regard. If you like this post, share it with your friends. This site uses Akismet to reduce spam. Learn how your comment data is processed.

Here is my full affiliate disclosure.Most bathroom faucets that have two handles are cartridge-style faucets. If you have a very old two-handle faucet, it may be a compression-type rather than a cartridge. You'll know when you remove the faucet handle: Cartridges are usually plastic and are held in place with a metal retaining nut; compression faucets usually have a metal valve with a flat rubber washer on the bottom.

If your two-handle faucet is leaking, feel the water to determine which side is leaking, hot or cold. You need to replace the cartridge on only the side that's leaking. However, it's possible that both sides are leaking and you'll have to replace both cartridges. Look under the sink to locate the shutoff valves on the water supply lines for the faucet. Most shutoff valves have a small, football-shaped handle or a lever that rotates.

Close the valve for the faucet tap you will be working on by turning the handle clockwise until it stops. Once the water is shut off, open the faucet fully to release any pressure in the water lines and let any water drain out.

Examine the faucet handle to determine how it is installed. Some handles have setscrews on the side or rear. Others have a decorative cap usually plastic that conceals a screw that secures the handle.

Your faucet may also have a removable lever that unscrews from the handle base to allow easy access to the handle setscrew. If your faucet has a decorative cap, pry off the cap with a small flathead screwdriver, then remove the handle screw with a Phillips screwdriver. If your faucet has a setscrew, remove the setscrew with an Allen wrench. Unscrew the nut all the way and remove it from the faucet body.

Its purpose is to reinforce the cartridge shaft when the faucet body's setscrew is tightened against it. You may need to remove this old screw and reuse it in the new cartridge, as not all replacement cartridges come with a new screw. Note the orientation of the faucet cartridge. You must reinstall the new cartridge in exactly the same way. Most cartridges have one or two tabs that fit into notches on the faucet body.

New cartridges typically include new rubber O-rings for the cartridge. If desired, also pick up some plumber's grease for the O-rings.

This makes it easier to insert the cartridge into the faucet body and is an especially good idea if the old cartridge was difficult to remove. Replace the little brass screw in the top of the cartridge shaft, if necessary. If you have plumber's grease, apply a small amount to the cartridge's O-rings, using your finger.

Insert the new cartridge into the faucet body in the same orientation as the original cartridge, aligning any tabs on the cartridge with the notch es on the faucet body. Push the cartridge all the way into the housing. Secure the cartridge with the retaining nut, tightening the nut carefully do not over-tighten with the wrench or pliers. Reinstall the faucet handle and setscrew or Phillips screw as well as the decorative cap, as applicable.

How to Remove a Kohler Revival Handle

Test the faucet for proper operation. Identifying Cartridge-Type Faucets. Flathead and Phillips screwdrivers Allen wrench Pipe wrench or tongue-and-groove pliers Replacement cartridge s Plumber's grease. Pull straight up on the handle to remove it from the faucet body. Read More.